How to fix sc code on samsung washer

Samsung washers are easy to use and reliable. Samsung is a household name, but the Samsung washer SC error code indicates that there is a drainage issue with the machine.

Índice Show

What Does The Samsung Washer SC Error Code Mean?
Wrong Cycle Selected
Clogged or Kinked Drain Hose
Improper Drain Height
Clogged Drain Pump Filter
Defective Lid Switch
What can cause the SC Error?
How to fix the SC Error?

Samsung washing machines have a filter in the water tank that needs to be cleaned regularly, and the Samsung drain hose should be clear of any blockages or kinks for it to work properly.

The instructions for checking the filter and unkinking the drain hose are included below, along with some other common Samsung washing machine problems and their solutions.

What Does The Samsung Washer SC Error Code Mean?

Your washer is a complex appliance, and sometimes there can be more wrong with it than just a bad smell or stain. Sometimes you’ll see lights flashing on your device’s LED display or a code displayed prominently on the screen.

These codes are vital in diagnosing problems that need to be fixed by a technician, and knowing them can help you save yourself from unnecessary purchases or expensive visits to the repair shop.

Samsung Washers display error code 5C when they detect a drainage problem. The most common causes of this problem are clogs in the pipe or drain hose, as well as a blocked filter.

Samsung washing machines use a pressure switch to detect when the drum is full. When the machine detects that the drum is full and water needs to be drained, it uses a pressure switch to open the drain valve.

If this doesn’t occur, you may experience the error code “SC.” On occasion, an unplugging and reconnecting of the washer will fix this issue.

Wrong Cycle Selected

Choosing the wrong wash cycle or spin speed is one of the most common reasons for a Samsung washer not draining. “Delicate” or “Hand wash” cycles may use lower spin speeds to treat certain fabrics more gently. This can leave clothes wetter at the end of a cycle or sitting in residual water.

If you choose the “Low” or “No Spin” spin speed option, clothes will remain somewhat wet, and water will be left in the machine. Choosing a “Heavy Duty” cycle with a higher spin speed will help to drain all of the remaining water from your clothes.

Clogged or Kinked Drain Hose

A simple visual inspection easily resolves many washing machine problems. If the washing machine is not draining, first check the hose for a kink or obstruction that might be preventing water from leaving the machine.

The hose that carries water from the back of the machine to your sink or drain could be kinked or otherwise obstructed. It would ultimately block the flow of water out of the machine.

The wash cycle also causes the drain hose to expand, allowing water to flow more freely. If your washing machine does not drain properly, make sure to check if it is too close to the wall or an appliance; this could prevent it from draining completely.

Sometimes clogs in the washer drain hose can be cleared by shining a flashlight into the hose and inspecting for any obstruction.

If you can’t see what’s causing the blockage, try taking off the drain hose and running water through it with a garden hose. Then, reconnect the drain hose to the machine and run a rinse cycle to see if you’ve solved the Samsung Washer SC Error Code.

Improper Drain Height

It’s simple, really: If you place your washing machine too high from the floor, it won’t be able to pump water out of the tub. And even if draining occurs, it will take longer than normal. Check your user manual for proper drain pipe installation and height recommendations.

Clogged Drain Pump Filter

If your washer isn’t draining well, the first thing you should check is the drain pump filter. These filters are designed to keep little pieces of dirt and debris from clogging up the drainage system, which could keep water from draining out of your machine.

The most common way to access this filter is through a small door located at the bottom right corner of the machine.

When your Samsung washing machine is clogged, first remove the filter to check if any debris or objects stuck inside cause the problem. To do this, open your washing machine’s door and pull out the filter from underneath.

Next, dispose of any foreign objects that you find using a trash bin, and rinse the filter under flowing water before returning it to its place.

Defective Lid Switch

Top loaders have an internal switch that prevents the spin cycle from starting if the lid is open. If you forget to close the lid after loading clothes or open it in the middle of a cycle, your top loader may not be able to spin your laundry. To resume a wash cycle after adding clothing or lifting the lid, simply press “Start” again.

In cases where the lid switch is faulty, a Samsung washing machine may not drain its water. A multimeter test on a faulty switch will display a lack of continuity between the terminals.

When this happens, the washing machine will not drain its water. Replace the faulty switch to resolve the Samsung Washer SC Error Code issue.

The SC Error code on the display of your Samsung device, which is also indicated as SE and read as 5C or 5E, signalizes a failure of the water drainage system of the washer.

This signifies the machine can not drain water after the end of the cycle and stops all the operations. Normally a notification will occur on the panel when the machine stops washing and should switch to rinse mode.

On the models without any screen, the same error is indicated by the blinking of the 40C temperature bulb and all the mode lights.

What can cause the SC Error?

Code SE/5E means that a fault has occurred in the water drain system. Or some reason your appliance is not able to drain water, so it interrupts the cycle and dis-plays an error.

It is a pretty common error for modern washers and in half of the cases, it can be easily fixed without any professional help. But first, the reason has to be determined.

The reasons can be different. The most common is the clog in the filter or the drain hose, which doesn’t let the water drain and provoke the error.

There also might be a failure of the drain pump. It can be broken or burnt-out and in need of a replacement. This error is usually shown on the screen when the contacts of the pump are loosened or disconnected.

The clog may occur not only in the hose and filter but also in the pump and nozzles. If you keep washing your clothes with foreign objects in the pockets, sooner or later you will face this problem.

The same error can be caused by the damaged pressure switch and malfunction of the control unit, which is the rarest of all the possible reasons, but still possible.

How to fix the SC Error?

First of all, turn the device off and unplug it from the power supply. Resume the washer to see if it helped in resetting the error. If it did not — you need to drain the water from the tank before proceeding with examination. Let the water out through the emergency drainage door and take out the garments from the drum.

The first things to check after the device is prepared are the drain hose and filter. Inspect the hosepipe on all the possible signs of damage and breakage, then check it for clogs from the inside, clean if needed. Look whether it is installed properly and fixed tightly without any gaps between the pipe and the body of the appliance.

To access the filter opens the small dot which is in the bottom right corner of the front machine’s panel. Take it off and check for clogs and foreign objects. Rinse it thoroughly and install back, screwing clockwise.

The next step is to inspect the drain nozzle, as it also can be clogged. After cleaning it try to run the washing cycle again and see if the water drains properly through the nozzle, but first, you have to detach the hosepipe.

If its all good with the drainage system but the SC Error code is still indicated, pro-ceed with the drain pump examination. There can be two issues here — the clog or the bad wire connection. The clog is pretty easy to see and clean. As for the wires, check every cable and pipe between the pump and the control unit, as some of them can be not connected properly or damaged. In this case, the damaged wires have to be replaced.

Another common failure causing the SC error is the malfunction of the pump. Whether it is in order or not can be tested with the help of the multimeter. The normal resistance level has to be around 165 Ohms. If it is not close, the pump has to be repaired or replaced by a specialist.

If after examination of drainage and pump systems you were not able to determine the reason for the SC error, the only place left to check is the pressure system and the pressure switch. As for the system can be simply plugged and it is easy to test by detaching the rubber tube from the system and blowing in it.

In the case of the problems of the pressure switch, check it for visible damage, fix all the wires and test it with the multimeter. Probably it has to be replaced.

Another probable reason can be in the malfunction of the main unit, but in the case, with electronic components of your appliance it is not recommended to carry out any repairs on your own, best is to contact the service center for a proper diagnostic.